Padding- body insulates the beam of the joined veins, it gives to entire adhesion form and makes for the sake of its compact. Based on each end down the clutch it is possible to bring to the 4th cables, using in this case the three-pin clamps, covered for the sake of thermo-fusible glue.

The wide range of the sizes of clutches makes it possible to use clutch XAGA-500 on the cables with capacity to 1200 pairs, and clutch XAGA-550 on the cables with capacity to 3600 pairs.


Marking clutches and basic dimensions before the mm.

Marking	Max. the diameter the adhesion	Min. [naruzh]. the diameter the cable	Distance between by the shear the shells	General the length	[Razvetvi]- body the complete set
	D	d	L	S
Clutch XAGA of 500-43/8-150-SU	43	8	150	350	Small
Clutch XAGA of 500-43/8-300-SU	43	8	300	500	Small
Clutch XAGA of 500-55/12-150-SU	55	12	150	360	Small
Clutch XAGA of 500-55/12-300-SU	55	12	300	510	Small
Clutch XAGA of 500-75/15-240-SU	75	15	240	480	Small
Clutch XAGA of 500-75/15-300-SU	75	15	300	540	Small
Clutch XAGA of 500-75/15-400-SU	75	15	400	640	Small
Clutch XAGA of 500-75/15-500-SU	75	15	500	740	Small
Clutch XAGA of 500-100/25-260-SU	100	25	260	580	Average
Clutch XAGA of 500-100/25-460-SU	100	25	460	780	Average
Clutch XAGA of 500-100/25-500-SU	100	25	500	810	Average
Clutch XAGA of 500-125/30-265-SU	125	30	265	600	Average
Clutch XAGA of 500-125/30-460-SU	125	30	460	800	Average

Selection of the clutch

With conclusion of two and more than cables based on one end it is necessary to calculate their total diameter. In this case to the sum of the diameters of cables should be added on 6 mm down each small clamp or 8 mm and each average clamp. In any event total diameter must not exceed the maximum permissible diameter of beam it lived before the place of adhesion for this type of clutch.

Before the example in question should be selected the clutch XAGA of 500-75/15-[khkhkh] or XAGA 550-75/15- of [khkhkh]; moreover the values of [khkhkh] will [zavisit] from the length of adhesion (L)


Composition of the set of the clutch:

• Heat-shrinkable sleeve
• Flexible fastenings through the stainless steel
• Stopping yoke
• the Padding- body
• Napkin for the rub
• Tape of the emery paper
• Absorber of moisture (silica gel)
• Aluminum foil
• Complete set for the splitting connections
• Wire with the clamps for guaranteeing the continuity of the screen
• Measuring template
• Installation specifications (before the Russian language)

Splitting complete set
Composition:

• Splitting clamp
• Wire with the clamp for guaranteeing the continuity of the screen
• Napkin for the rub
• [Alyuminevaya] foil
• Plastic belt

Marking:

[VOKT]-5S-43/8-75/15 [Razmetvitelnyy] complete set with the small clamp.
[VOKT]-5M-92/25-125/30 [Razmetvitelnyy] complete set with the average clamp.
[VOKT]-5L-160/42-200/50 [Razmetvitelnyy] complete set with the large clamp.