10- paired, 20- paired and 25- paired versions.

Rapid inosculation of copper cables.

The complete installation of 10- paired module is carried out on the average in 4,5 minutes.

IS NOT REQUIRED the cleaning of isolation, joining, soldering through and insulating of veins.

Universality: the different types of the connections of veins with the diameter of 0,32-0,9 mm for the sake of different isolation.

Reliable electrical contact.
Reliable mechanical connection.

Modules for 10, 20 and 25 pairs are developed for the rapid inosculation of multipair copper communication cables for the sake of the diameter of veins 0,32-0,9 mm.

Veins are pressed beside the thin cuts of tinplated contact. Sharp of edge pierce plastic, paper or other isolation with the diameter not of more than 1,65 mm and ensure reliable contact.

The modules AMP STACK can be [ispolzovanny] for the direct inosculation and branching off the telephone cable.


There are three different types of the connecting modules:

	Direct inosculation - for the inosculation “entrance and output”
	Branching off - makes it possible “to branch” multipair cables without disruption of work, (as a rule, this it is used during the reorganization of cable).
	Connection - also can be used during the reorganization of cables and their replacement, t [k] makes it possible to connect one connector down another and to separate them if necessary.

All forms of the connecting modules AMP STACK (AMP STACK) can be both before the dry version and with the moisture-repelling filler. Special openings are provided for the signaling test of the installed connector. Module consists of two covers and housing with the built-in contacts.

AMP STACK Of mark OF THE IV-10- PAIRS
	Dry version the inosculation the transparent covers [PN] 1-737858-2 the colored covers [PN] 737858-2 the branching off the transparent covers [PN] 1-737860-2 the colored covers [PN] 737860-2 the connection the transparent covers [PN] 1-737859-2 the colored covers [PN] 737859-2	Version with the filler the inosculation the transparent covers [PN] 1-737869-2 the colored covers [PN] 737869-2 the branching off the transparent covers [PN] 1-737873-2 the colored covers [PN] 737873-2 the connection the transparent covers [PN] 1-737871-2 the colored covers [PN] 737871-2
AMP STACK Of mark OF THE III 20- PAIRS
	Dry version the inosculation the transparent covers [PN] 1-737771-2 the colored covers [PN] 737771-2 the branching off the transparent covers [PN] 1-737772-2 the colored covers [PN] 737772-2	Version with the filler the inosculation the transparent covers [PN] 1-737861-2 the colored covers [PN] 737861-2 the branching off the transparent covers [PN] 1-737863-2 the colored covers [PN] 737863-2
AMP STACK Of mark OF THE III 25- PAIRS
	Dry version the inosculation the transparent covers [PN] 1-737692-2 the colored covers [PN] 737692-2 the branching off the transparent covers [PN] 1-737708-2 the colored covers [PN] 737708-2 the connection the transparent covers [PN] 1-737707-2 the colored covers [PN] 737707-2	Version with the filler the inosculation the transparent covers [PN] 1-737830-2 the colored covers [PN] 737830-2 the branching off the transparent covers [PN] 1-737834-2 the colored covers [PN] 737834-2 the connection the transparent covers [PN] 1-737832-2 colored covers [PN] 737832-2

Systems for protection from external actions

Container, filled for the sake of the hydrophobic gel

System of the protection of [soeditelnykh] modules AMP.

Simple device of the depression of modules (applicator).

Protection from the external actions (moisture, water, temperature and other).

Technical documentation and instruction before the Russian language.

It adapts with the modules of inosculation together with the connected module.

The sealing container ensures the additional protection of the modules AMP STACK. The need of applying this protection is justified due to the ex-threesmall conditions (water, temperature variations, the increased humidity).

Container with the gel easily is established beyond the module without the use of complex tools. Each packing contains applicator for the depression of module inside the container. It is necessary to be certified before the correctness of the installation of module before the application of a container. If the need for verifying the module inserted beside the container arose, it is necessary to extract it, to carry out all necessary testing, to after which use for the protection a new container. The containers, utilized only with the modules of inosculation, differ regarding color from those used with the connected modules of inosculation and connection. The corresponding applicators also differ before the color.

AMP STACK	Module	[PN]	Color
Mark IV of 10 Pairs Mark IV of 10 Pairs Mark OF III 25 Pairs Mark OF III 25 Pairs	Inosculation Inosculation, the connection Inosculation Inosculation, the connection	336282-1 336282-2 737823-1 737823-2	Yellow Red Yellow Red

Tools

Tools AMP STACK for the 10- paired, 20- paired and 25- paired modules Mark OF THE III and brand IV

For the pressing of multipair modules AMP it proposes the small mechanical tools, which combine before themselves universality and simplicity. With their aid it is possible to make inosculation and. Ratchet mechanism makes it possible not to worry about the quality of connection. Tool it is not possible to open thus far pressing is not completely completed.

Tools of this type are very reliable and do not require special withdrawal. The numerous tests of the large number of copies showed that not less than 10.000 cycles (pressings) it is possible to make without additional lubricant and cleaning.

The installation of modules is achieved before the assembly heads, which in turn are fastened down the lath.

Tools are proposed as complete set before the compact trunk together with the holder of head. Holder makes it possible to conveniently fasten tool on the post or before the well on the existing cable. They enter into the composition of [kompekta]: tool, assembly head, lath, tool for the closing of single veins, template for checking the polarity of pairs, holder and trunk for the carrying-over.


Hand press AMP STACK for the 10- paired modules brand IV
Weight of 1 kg.
With the pressing of vein with the diameter of 0,5 mm the effort is not more than 9 kg.
AMP STACK Of tool of 10 Pair
Tool for the 10- paired connectors before the compact trunk
[PN] 790142-2


[Vspomagatelnye] equipment

Single separating tool	Splitting assembly head	T-shaped fastening
This tool is developed for separation of the connected module from another module, down which it is connected. It adapts with all modules AMP STACK	Additional assembly head with two fixing springs, located based on two sides. It is intended for the installation of the modules of branching off due to the conditions of the difficult access to the [soeditelnym] cables. It is compatible only with the 25- paired press AMP	T-shaped fastening is developed for positioning on it one or two 10- paired assembly heads or of one 25- paired. It can be used as adapter with some models of holders.
[PN] 0-790141-1	[PN] 1-525421-4	[PN] 0-790136-1

Tools AMP STACK

for the 25- paired and 20- paired modules

Weight 1,7 kg.

With the pressing of vein with the diameter of 0,5 mm the effort is not more than 25 kg.

Using a special adapter, it is possible to begin pressing 20- paired module.

25- paired tool before the compact trunk

[PN] 318433-2


The auxiliary equipment

Universal holder for 10- and the 25- paired tool for the fastening on the cable [PN] 790144-1

the 20- paired adapter [PN] 356325-1

[Vspomagatelnye] equipment

Capacious, lungs, durable, convenient, facilitate labor.

Bags for 20 and the 25- paired modules
It is used for arrangement 20 and 25- paired modules during the installation.
[PN] 0-790160-1
It is used for positioning the 10- paired modules during the installation.
[PN] 0-790160-2

Carring strap
It is supplied for the sake of two carbines. It makes it possible to hang up bag against the work site
[PN] 0-790158-1

The waist belt
It makes it possible to fasten bag on the [poyasem] of the fitter
[PN] 0-790161-1


Holder and the [vspomagatelnye] tools

the 10- paired separating tool [PN] 0-790104-1 Tool for the closing single veins [PN] 0-224290-1	For the airlines! Fastening down the post [PN] 0-224286-1	Adapter for the signaling test [PN] 0-790106-1